1: Ensure the surface onto which you intend to apply the transfer is clean and grease-and dust-free. THE SURFACE SHOULD PREFERABLY BE OF A GLOSS FINISH. The more matt the finish, the less likely it is that successful adhesion will take place and the more likely it is that even the miniscule amount of carrier film will show up.

2: Cut the transfer from the sheet, allowing a margin around the image. Do not cut into the printed image unless you are deliberately reducing the area of transfer to be applied, eg:cutting lining down to size either depthways or lengthways.

3: Immerse the transfer in a saucer or trough of warm water for a few seconds. The container of water should preferably be large enough to accommodate the full, flat transfer. Owing to modified chemistry, we now recommend that you add a drop of washing up liquid to the warm water. The transfer will initially curl up, then partially flatten out. Test whether the transfer has become detached from the backing sheet by gentle pressure with a finger. The larger the transfer, the longer it will take to separate from the backing paper. Use warm water - not hot - not cold - and certainly not of boiling temperature.

4: When separation has occurred, remove the transfer and the backing paper as one item, position in the required location retaining the image in position with light pressure whilst sliding out the backing paper and disposing.

5: Make final adjustments to the position, at the same time dabbing off excess water with an absorbent cloth or blotting paper. Ensure there are no air- or water-bubbles trapped between transfer and location surface by gentle outward stroking of cloth or blotter to edges of transfer.

 

Guidance:

-Ensure that the transfer is properly soaked before you attempt to remove it from the backing paper. A simple test is to check that there is no ‘drag’ on the paper, and that the transfer slides off smoothly.

-Where, for instance, a long line of otherwise unsupported lettering is involved, slide the transfer backing paper in such a way that the transfer has to move the minimum distance, ie not lengthways. This will lessen the stress of the carrier film and reduce the likelihood of the transfer breaking up.

-The less handling and adjustment your transfer receives to position correctly, the better the adhesion is likely to be, and the less likely it is that damage will occur.

-In certain circumstances, you may find it necessary to manipulate a transfer for quite some time to obtain your desired position, eg. around small detail. This may involve the application of extra water to maintain the transfer’s mobility. To avoid over-diluting the adhesive on the back of the transfer, ensure that the small amount of extra water required has lain on scrap transfer backing paper prior to using it to further move the transfer.

6: Allow to dry completely, preferably for several hours, eg: overnight. When all transfers have been applied and allowed to dry, Fox Transfers strongly recommend that a protective coat of a suitable varnish in gloss, satin or matt finish is applied over the transfer. This should be carried out particularly in circumstances where the transfer is positioned on an exterior surface, or where the model will be handled and DEFINITELY where the transfer is likely to come into contact with chemicals of any description, for example a carriage washing unit, where the cleaning agents employed have extremely deleterious effect on all transfers, paint and other surfaces.

Fox Specific Lining Packs

The transfers in this pack have been carefully prepared for you, following painstaking research into both the original vehicles and using the models or kits onto which they are likely to be applied.

It must be emphasised that application to your model of some of the elements - especially tender, cab and tank panels - is a task which requires a great deal of care and patience, but which if carried out correctly should give a far superior finish to your work. 

We recommend initial marking-out of the extremities of each lining panel on your model, using either masking tape or a very faint blade mark with your craft knife or scalpel. Then cut the transfer panel about halfway along each side. Apply each section separately following the instructions on the transfer pack, only progressing to the next section when you are completely happy with the positioning of the one in hand. Butt-join each piece of transfer to the previous piece, ensuring no space is left between pieces and that they do not overlap.

We recommend that you use this proceedure (cutting the transfer to a manageable length) with all fine lining transfers.

 

Please remember:

1: THE BEST SURFACE FOR ADHESION OF TRANSFERS IS A GLOSS SURFACE. When the transfers have cured, you should over-varnish them for protection with a clear varnish of your choice - matt, satin (eggshell) or gloss.

2: DO NOT TOUCH THE SURFACE OF THE MODEL WHERE YOU INTEND TO APPLY TRANSFERS. EVEN YOUR FINGERS CAN LEAVE GREASY DEPOSITS WHICH WILL IMPEDE SUCCESSFUL APPLICATION. Ensure the surface is dust and grease-free.

3: DO NOT RUSH APPLICATION OF TRANSFERS. 

If you have spent weeks or months building your model - or even just re-painting it - it is unreasonable to expect to apply the transfers in a couple of  hours. Your patience will be rewarded with a model you’ll be proud to exhibit.

NAMEPLATES APPLICATION INSTRUCTIONS